Language Selector

Wiki

FrontPage

13483544 Views
Average (27 Votes)

Message Boards

Canon BJC-85 Driver, Firmware and Manuals for Windows and MacOS

DN
Dang Nam, modified 1 Month ago.

Canon BJC-85 Driver, Firmware and Manuals for Windows and MacOS

Yoda Posts: 1354 Join Date: 4/26/21 Recent Posts
Canon BJC-85 Driver, Firmware and Manuals for Windows and MacOS

There are many drivers, software and settings to choose from on the https://dnasofts.com/ website for your Canon product that will work with each operating system or without driver software! Click below to learn more about compatibility details of products in detail.
Users enjoy the unique features of BJC-85 printer, which stands out from its counterparts. This multifunctional machine can print and copy documents with exceptional quality as well as scan them for faxing! It is powered by an Automatic Document Feeder (ADF) so you never have to worry about running low on paper again either- just load up your roll once it has been built into your Canon BJC-85 printer model.
In terms of speed, depending what level duplex printing or single sided mode that one chooses when using certain models may alter how quickly they output at many pages per minute

Canon BJC-85 Driver, Firmware and Manuals for Windows and MacOS

Get Epson printer driver, firmware and manual more over here: https://dnasofts.com/

Canon BJC-85 Driver

- Canon BJC-85 printer driver is a great way to stay up-to date with your office's printing devices! You can monitor the warning signs that an ink cartridge needs changing, check out any errors during scanning photos from one side onto paper produced by another (blurred), and more.
- So, what's the point? It <b/>won't let them hack into Computer Utilities & Cracking Tools Resets Chips
- With all these hackers out there who can access any WIC utility tool reset chip or crack adjustment program that you may have. The best way would be via purchasing a license key from https://nguyendangnam.com/ so they only get their hands on those printer drivers which allow us to fix 'paper jam' issues in our printers!

Download Canon BJC-85 Driver for Windows:

- Download Canon BJC-85 Driver for Windows 11: DOWNLOAD LINK

- Download Canon BJC-85 Driver for Windows 10 64bit: DOWNLOAD LINK

- Download Canon BJC-85 Driver for Windows 10 32bit: DOWNLOAD LINK

- Download Canon BJC-85 Driver for Windows 8 64bit: DOWNLOAD LINK

- Download Canon BJC-85 Driver for Windows 8 32bit: DOWNLOAD LINK

- Download Canon BJC-85 Driver for Windows 7 64bit: DOWNLOAD LINK

- Download Canon BJC-85 Driver for Windows 7 32bit: DOWNLOAD LINK

Download Canon BJC-85 printer Driver for Mac OS:

- Download Canon BJC-85 Driver for Mac OS 11.xx: DOWNLOAD LINK

- Download Canon BJC-85 Driver for Mac OS 10.xx: DOWNLOAD LINK

How to download softwares or documents of Canon BJC-85

STEP 1: Go to our website and search for "Canon BJC-85 driver, firmware, manual"

STEP 2: Choose your specific Canon BJC-85 driver, firmware and manual and click to Download button image

STEP 3: Wait for the downloading webpage and download the software

Canon BJC-85 driver, firmware, manual downloading webpage

STEP 4: Your downloaded file has been located in Browser Downloaded Page

Canon BJC-85 driver, firmware, manual downloaded file

STEP 5: Read the instructions to install and start using the softwares.

Canon BJC-85 Firmware

- The Canon BJC-85 Firmware is an intermediary software developed by Canon company, which helps to interact between the software and the hardware of the printer with each other. It is used when printing from a computer or sending print jobs from one device to another via WiFi Direct/Ethernet direct connection.
- Canon BJC-85 needs to be refilled by the the original firmware when the printer components are unstable or the printer went wrong with the teachnical error or firmware errors. By that time, you need a technician or experienced person to fix Canon BJC-85 and diagnose the problems for your printer.- The Canon BJC-85 printer is more than just a means of reproduction, it has evolved into an essential tool for home and office use. When you need to troubleshoot or service your device call the pros at https://dnasofts.com/!
The Canon BJC-85 original firmware can fix some errors related with hardware like sensors failure--restarting them in time so they don't fail repeatedly; circuit problems preventing electricity from flowing properly through components on print heads etc...
The Canon BJC-85 original firmware in your printer is the software that allows it to function. With firmware, Canon BJC-85 printer can be updated remotely via updates sent by manufacturers, which affect how you use and accomplish tasks with your Canon BJC-85 printer - for example speeding up printing time!
Canon BJC-85 Original Firmware is the software that controls your printer. It allows it to communicate with a computer and do what you want, like printing or copying things! The chip inside this device can be updated remotely so if there are any problems fixed in an update then they will fix them because of how close these two work together.

Download Original Canon BJC-85 Firmware for Windows:

- Original Canon BJC-85 Firmware for Windows: DOWNLOAD LINK

Download Canon BJC-85 Firmware for Mac OS:

- Original Canon BJC-85 Firmware for Mac OS: DOWNLOAD LINK

Canon BJC-85 User Manual

- A Canon BJC-85 printer's User Manual is a guide that comes with the purchase of your device. It provides instructions on how to correctly configure, assemble and use it as well as information about troubleshooting problems should they occur - this makes sure you don't have call customer service!
- By using Canon BJC-85 Manual, you can follow the instructions of the ebook and then you are able to fix errors code or common error like printer is unresponsive, bad print quality, printer won't scan, too many paper jams, prints too slowly, printing is too expensive, can't print from mobile device, Wi-Fi printing takes too long, disassembly or assembly of printer, Canon BJC-85 maintenance, sensor errors, Canon BJC-85 software problem, printer went problem, Canon BJC-85 troubleshooting, printer cable connections inside the product, ...
You can use our guide in order to understand all aspects of using this device including installation process and proper usage guidelines so that you never run into any issues while printing or configuring your machine!

- Canon BJC-85 User Manuals for Windows: DOWNLOAD LINK

- Canon BJC-85 User Manuals for MacOS: DOWNLOAD LINK

[Quick guide] Fix Canon BJC-85 error code list

- Code: E001-A001
- Description: Fixing Main Thermistor high temperature detection error => The Fixing Main Thermistor detected 265 deg C or higher for 0.1 sec or longer.
- Solutions: [Related parts] - Fixing Assembly (Unit of replacement: Fixing Assembly) - Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK ASSEMBLY) - Harness between the Low-voltage Power Supply PCB (UN01/ J315 and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of replacement: CABLE, POWER SUPPLY) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Solutions] Check/replace the related parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES


- Code: E001-A002
- Description: Fixing Sub Thermistor (Front) high temperature detection error => The Fixing Sub Thermistor (Front) detected 290 deg C or higher for 0.1 sec or longer.
- Solutions: [Related parts] - Fixing Assembly (Unit of replacement: Fixing Assembly) - Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK ASSEMBLY) - Harness between the Low-voltage Power Supply PCB (UN01/ J315 and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of replacement: CABLE, POWER SUPPLY) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Solutions] Check/replace the related parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES


- Code: E001-A003
- Description: Fixing Sub Thermistor (Rear) high temperature detection error => The Fixing Sub Thermistor (Rear) detected 290 deg C or higher for 0.1 sec or longer.
- Solutions: [Related parts] - Fixing Assembly (Unit of replacement: Fixing Assembly) - Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK ASSEMBLY) - Harness between the Low-voltage Power Supply PCB (UN01/ J315 and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of replacement: CABLE, POWER SUPPLY) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Solutions] Check/replace the related parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES


- Code: E001-A004
- Description: Fixing Main Thermistor high temperature detection error => The Fixing Main Thermistor detected 270 deg C or higher
- Solutions: [Related parts] - Fixing Assembly (Unit of replacement: Fixing Assembly) - Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK ASSEMBLY) - Harness between the Low-voltage Power Supply PCB (UN01/ J315 and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of replacement: CABLE, POWER SUPPLY) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Solutions] Check/replace the related parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES


- Code: E001-A005
- Description: Fixing Sub Thermistor (Front) high temperature detection error => The Fixing Sub Thermistor (Front) detected 295 deg C or higher.
- Solutions: [Related parts] - Fixing Assembly (Unit of replacement: Fixing Assembly) - Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK ASSEMBLY) - Harness between the Low-voltage Power Supply PCB (UN01/ J315 and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of replacement: CABLE, POWER SUPPLY) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Solutions] Check/replace the related parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES


- Code: E001-A006
- Description: Fixing Sub Thermistor (Rear) high temperature detection error => The Fixing Sub Thermistor (Rear) detected 295 deg C or higher.
- Solutions: [Related parts] - Fixing Assembly (Unit of replacement: Fixing Assembly) - Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK ASSEMBLY) - Harness between the Low-voltage Power Supply PCB (UN01/ J315 and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of replacement: CABLE, POWER SUPPLY) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Solutions] Check/replace the related parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

- Code: E002-A001
- Description: Fixing Main Thermistor temperature increase detection error => The Fixing Main Thermistor detected a temperature increase of 1 deg C for less than 5 sec from turning ON the main power until start of PI control.
- Solutions: [Related parts] - Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) - Fixing Assembly (Unit of replacement: Fixing Assembly) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK ASSEMBLY) - Harness between the Low-voltage Power Supply PCB (UN01/ J315 and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of replacement: CABLE, POWER SUPPLY) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Solutions] Check/replace the related parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES


- Code: E002-A002
- Description: Fixing Main Thermistor open circuit detection error => The Fixing Main Thermistor detected a temperature of 40 deg C or lower for 3 sec or longer from turning ON the main power until start of PI control.
- Solutions: [Related parts] - Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) - Fixing Assembly (Unit of replacement: Fixing Assembly) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK ASSEMBLY) - Harness between the Low-voltage Power Supply PCB (UN01/ J315 and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of replacement: CABLE, POWER SUPPLY) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Solutions] Check/replace the related parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES


- Code: E002-A003
- Description: Fixing Sub Thermistor (Front) open circuit detection error => The Fixing Sub Thermistor (Front) detected a temperature of 40 deg C or lower for 3 sec or longer from turning ON the main power until start of PI control.
- Solutions: [Related parts] - Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) - Fixing Assembly (Unit of replacement: Fixing Assembly) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK ASSEMBLY) - Harness between the Low-voltage Power Supply PCB (UN01/ J315 and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of replacement: CABLE, POWER SUPPLY) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Solutions] Check/replace the related parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES


- Code: E002-A004
- Description: Fixing Sub Thermistor (Rear) open circuit detection error => The Fixing Sub Thermistor (Rear) detected a temperature of 40 deg C or lower for 3 sec or longer from turning ON the main power until start of PI control.
- Solutions: [Related parts] - Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) - Fixing Assembly (Unit of replacement: Fixing Assembly) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK ASSEMBLY) - Harness between the Low-voltage Power Supply PCB (UN01/ J315 and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of replacement: CABLE, POWER SUPPLY) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Solutions] Check/replace the related parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES


- Code: E003-A001
- Description: Fixing Main Thermistor low temperature detection error (during printing) => The Fixing Main Thermistor detected a temperature of 80 deg C or lower for 1 sec or longer from start of PI control until completion of the last rotation (the Fixing Heater is turned OFF) during printing.
- Solutions: [Related parts] - Fixing Assembly (Unit of replacement: Fixing Assembly) - Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK ASSEMBLY) - Harness between the Low-voltage Power Supply PCB (UN01/ J315 and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of replacement: CABLE, POWER SUPPLY) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Solutions] Check/replace the related parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES


- Code: E003-A002
- Description: Fixing Sub Thermistor (Front) low temperature detection error => The Fixing Sub Thermistor (Front) detected a temperature of 80 deg C or lower for 1 sec or longer from start of PI control until completion of the last rotation (the Fixing Heater is turned OFF) during printing.
- Solutions: [Related parts] - Fixing Assembly (Unit of replacement: Fixing Assembly) - Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) - Harness between the Fixing Drawer (DR01/J5401) and the Low-voltage Power Supply PCB (UN01/J302) (Unit of replacement: INTERLOCK ASSEMBLY) - Harness between the Low-voltage Power Supply PCB (UN01/ J315 and J322) and the DC Controller PCB (UN04/J20 and J22) (Unit of replacement: CABLE, POWER SUPPLY) - Harness between the Fixing Drawer (DR01/J5401) and the DC Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Solutions] Check/replace the related parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRESs

Support fix printer solution and reset Canon BJC-85:
– Telegramhttps://t.me/hyperaktiv
– Facebookhttps://www.facebook.com/dngnm/

Related sources:
https://nguyendangnam.com/
https://shop.nguyendangnam.com
https://nguyendangnam.com/download-epson-artisan-710-driver-firmware-users-manual-and-wic-key.html
Fix other error code list about printer, https://nguyendangnam.com/epson-driver
Fix other error code list about printer, https://nguyendangnam.com/error-code
https://shop.nguyendangnam.com/product-category/adjustment-program/

Calendar

VIET NAM's Calendars