Language Selector

Wiki

FrontPage

13631796 Views
Average (27 Votes)

Message Boards

Canon CX-G6400-4" Driver, Firmware and Manuals for Windows and MacOS

DN
Dang Nam, modified 1 Month ago.

Canon CX-G6400-4" Driver, Firmware and Manuals for Windows and MacOS

Yoda Posts: 1354 Join Date: 4/26/21 Recent Posts
Canon CX-G6400-4" Driver, Firmware and Manuals for Windows and MacOS

There are many drivers, software and settings to choose from on the https://dnasofts.com/ website for your Canon product that will work with each operating system or without driver software! Click below to learn more about compatibility details of products in detail.
Canon CX-G6400 4" Inkjet Card Printer printer is best suited for office use and its bundled with many features which makes it a productive and efficient machine. This product supports duplex printing and many other advanced features.

Canon CX-G6400-4

Get Epson printer driver, firmware and manual more over here: https://dnasofts.com/

Canon CX-G6400-4" Driver

- Canon CX-G6400-4" Drivers are needed for connecting Canon CX-G6400-4" to your computer. You can use this software program not only monitor warning parts need repair, but also track where printing progress is at and other important information about how much ink or paper remains in the machine!
- At first glance, it is difficult to understand why anyone would need a driver that fixes Canon CX-G6400-4" printer errors and issues. However there are many reasons someone might have this installed on their computer--maybe they got one piece of paper stuck in the machine causing an 'Paper Jam' error code while trying other things with Photoshop or Microsoft Office? Or maybe you were running low on ink so wanted try cleaning out some dirt inside before calling for help; either way if any type of problem arises users should know exactly where too find WIC utility reset chip (or hack adjustment programs) because finding them elsewhere will only lead more trouble later down road

Download Canon CX-G6400-4" Driver for Windows:

- Download Canon CX-G6400-4" Driver for Windows 11: DOWNLOAD LINK

- Download Canon CX-G6400-4" Driver for Windows 10 64bit: DOWNLOAD LINK

- Download Canon CX-G6400-4" Driver for Windows 10 32bit: DOWNLOAD LINK

- Download Canon CX-G6400-4" Driver for Windows 8 64bit: DOWNLOAD LINK

- Download Canon CX-G6400-4" Driver for Windows 8 32bit: DOWNLOAD LINK

- Download Canon CX-G6400-4" Driver for Windows 7 64bit: DOWNLOAD LINK

- Download Canon CX-G6400-4" Driver for Windows 7 32bit: DOWNLOAD LINK

Download Canon CX-G6400-4" printer Driver for Mac OS:

- Download Canon CX-G6400-4" Driver for Mac OS 11.xx: DOWNLOAD LINK

- Download Canon CX-G6400-4" Driver for Mac OS 10.xx: DOWNLOAD LINK

How to download softwares or documents of Canon CX-G6400-4"

STEP 1: Go to our website and search for "Canon CX-G6400-4" driver, firmware, manual"

STEP 2: Choose your specific Canon CX-G6400-4" driver, firmware and manual and click to Download button image

STEP 3: Wait for the downloading webpage and download the software

Canon CX-G6400-4

STEP 4: Your downloaded file has been located in Browser Downloaded Page

Canon CX-G6400-4

STEP 5: Read the instructions to install and start using the softwares.

Canon CX-G6400-4" Firmware

- When you use Canon CX-G6400-4" printer to print from a computer or sending jobs to another device, you need the Canon CX-G6400-4" 's firmware. But if it gets stuck in an error state and can't be fixed by itself anymore then refilling with original Canon CX-G6400-4" firmware will come handy as this helps fix unstable components of your machine while diagnosing technical errors occurring on both hardware level with software related problems
- The package also includes all necessary tools that are used during these procedures so there isn't anything lost along
- The printer errors can make you feel frustrated when you don't know what caused your problem. Original Firmware, or in layman's terms "printer firmware" is developed by Epson company which helps interact between themselves and their hardware during printing either from computer-based operations or Wi-Fi Direct connections over Ethernet cables direct connection via WIMAX networks

Download Original Canon CX-G6400-4" Firmware for Windows:

- Original Canon CX-G6400-4" Firmware for Windows: DOWNLOAD LINK

Download Canon CX-G6400-4" Firmware for Mac OS:

- Original Canon CX-G6400-4" Firmware for Mac OS: DOWNLOAD LINK

Canon CX-G6400-4" User Manual

- Canon CX-G6400-4" User Manual also called Canon CX-G6400 4" Inkjet Card Printer User's Guide, which is provided by Epson company after you had purchasing a product.
- This Canon CX-G6400-4" printer guides include instructions such as basic disassembly of the printer, disassembly of the cartridge, instructions on choice of ink type, ink pump for printer and how to configure the printer to print via LAN /Wifi. It also has information about troubleshooting problems with printers and how to fix them yourself without having to call customer service.
- By using Canon CX-G6400-4" Manual, you can follow the instructions of the ebook and then you are able to fix errors code or common error like printer is unresponsive, bad print quality, printer won't scan, too many paper jams, prints too slowly, printing is too expensive, can't print from mobile device, Wi-Fi printing takes too long, disassembly or assembly of printer, Canon CX-G6400-4" maintenance, sensor errors, Canon CX-G6400-4" software problem, printer went problem, Canon CX-G6400-4" troubleshooting, printer cable connections inside the product, ...
You can use our guide in order to understand all aspects of using this device including installation process and proper usage guidelines so that you never run into any issues while printing or configuring your machine!

- Canon CX-G6400-4" User Manuals for Windows: DOWNLOAD LINK

- Canon CX-G6400-4" User Manuals for MacOS: DOWNLOAD LINK

[Quick guide] Fix Canon CX-G6400-4" error code list

- Code: E001-0001
- Description: Main Thermistor high temperature detection => Main Thermistor 2 detected a temperature of 230 deg C or higher for 0.1 sec or longer.
- Solutions: Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/J12) and the Fixing Assembly (UN37/J123,UN13/J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Disconnect the connector of DC Controller PCB (UN09/J12) and start the host machine to check the reading value of the following: service mode > COPIER > DISPLAY > ANALOG > FIX-C => When the value is 40 deg C or higher 3-1. Replace the DC Controller PCB (UN09) => When the value is lower than 40 deg C 3-2. Replace the Fixing Assembly NOTE: After performing the above Solutions work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR


- Code: E001-0002
- Description: Center Thermistor high temperature detection => Main Thermistor 1 detected a temperature of 283 deg C or higher for 0.1 sec or longer.
- Solutions: Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Disconnect the connector of DC Controller PCB (UN09/ J12) and start the host machine to check the reading value of the following: service mode > COPIER > DISPLAY > ANALOG > FIX-E => When the value is 40 deg C or higher 3-1. Replace the DC Controller PCB (UN09) => When the value is lower than 40 deg C 3-2. Replace the Fixing Assembly NOTE: After performing the above Solutions work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR


- Code: E001-0003
- Description: Edge Thermistor high temperature detection => Sub Thermistor 1 detected a temperature of 283 deg C or higher for 0.1 sec or longer.
- Solutions: Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Disconnect the connector of DC Controller PCB (UN09/ J12) and start the host machine to check the reading value of the following: service mode > COPIER > DISPLAY > ANALOG > FIX-E2 => When the value is 40 deg C or higher 3-1. Replace the DC Controller PCB (UN09) => When the value is lower than 40 deg C 3-2. Replace the Fixing Assembly NOTE: After performing the above Solutions work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR


- Code: E001-0004
- Description: Edge Thermistor high temperature detection => Sub Thermistor 2 detected a temperature of 283 deg C or higher for 0.1 sec or longer.
- Solutions: Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Disconnect the connector of DC Controller PCB (UN09/ J12) and start the host machine to check the reading value of the following: service mode > COPIER > DISPLAY > ANALOG > FIX-E3 => When the value is 40 deg C or higher 3-1. Replace the DC Controller PCB (UN09) => When the value is lower than 40 deg C 3-2. Replace the Fixing Assembly NOTE: After performing the above Solutions work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR


- Code: E001-0005
- Description: Center Thermistor high temperature detection => Main Thermistor 1 hardware signal is continued for 1 sec or longer.
- Solutions: Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Disconnect the connector of DC Controller PCB (UN09/ J12) and start the host machine to check the reading value of the following: service mode > COPIER > DISPLAY > ANALOG > FIX-E => When the value is 40 deg C or higher 3-1. Replace the DC Controller PCB (UN09) => When the value is lower than 40 deg C 3-2. Replace the Fixing Assembly NOTE: After performing the above Solutions work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR


- Code: E001-0006
- Description: Edge Thermistor high temperature detection => Sub Thermistor 1 hardware error detection signal is continued for 1 sec or longer.
- Solutions: Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Disconnect the connector of DC Controller PCB (UN09/ J12) and start the host machine to check the reading value of the following: service mode > COPIER > DISPLAY > ANALOG > FIX-E2 => When the value is 40 deg C or higher 3-1. Replace the DC Controller PCB (UN09) => When the value is lower than 40 deg C 3-2. Replace the Fixing Assembly NOTE: After performing the above Solutions work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR

- Code: E001-0007
- Description: Edge Thermistor high temperature detection => Sub Thermistor 2 hardware error detection signal is continued for 1 sec or longer.
- Solutions: Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Disconnect the connector of DC Controller PCB (UN09/ J12) and start the host machine to check the reading value of the following: service mode > COPIER > DISPLAY > ANALOG > FIX-C Check the reading value of the following: service mode > COPIER > DISPLAY > ANALOG > FIX-E3 => When the value is 40 deg C or higher 3-1. Replace the DC Controller PCB (UN09) => When the value is lower than 40 deg C 3-2. Replace the Fixing Assembly NOTE: After performing the above Solutions work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR


- Code: E001-0008
- Description: Displacement detection => The temperature difference between the Sub Thermistor 1 (TH3) and the Sub Thermistor 2 (TH4) remained 45 deg C or more for 1 second or more.
- Solutions: Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Disconnect the connector of DC Controller PCB (UN09/ J12) and start the host machine to check the reading value of the following: service mode > COPIER > DISPLAY > ANALOG > FIX-E2,FIX-E3 => When the value of either one is 40 deg C or higher 3-1. Replace the DC Controller PCB (UN09) => When the both values are lower than 40 deg C 3-2. Replace the Fixing Assembly NOTE: After performing the above Solutions work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR


- Code: E002-0006
- Description: Detection of abnormal temperature increase => Fixing Assembly error, Fixing temperature detection error
- Solutions: 1. Check the location for voltage of the Fixing Assembly -> Replace with a correct Fixing Assembly for the location in the case of mismatching. 2. Check the location for voltage of the AC Driver PCB (UN14) -> Replace with a correct AC Driver PCB (UN14) for the location in the case of mismatching. 3. Check failure between the AC Driver PCB (UN14/J103) and the Fixing Assembly (UN37/J123, UN13/J13). (trapped cable, open circuit, connector disconnection) -> Replace the part in the case of trapped cable/open circuit 4. Replace the AC Driver PCB (UN14) 5. Replace the Fixing Assembly 6. Replace the DC Controller PCB (UN09) NOTE: After performing the above Solutions work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR


- Code: E003-0001
- Description: Thermistor open circuit detection => In the period from initial rotation to printing, Main Thermistor 1 detected a temperature of 22 deg C or lower for more than 5 seconds.
- Solutions: Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Replace the Fixing Assembly 3. Replace the DC Controller PCB (UN09) NOTE: After performing the above Solutions work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR


- Code: E003-0002
- Description: Thermistor open circuit detection => In the period from initial rotation to printing, Main Thermistor 2 detected a temperature of 40 deg C or lower for more than 3 seconds.
- Solutions: Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Replace the Fixing Assembly 3. Replace the DC Controller PCB (UN09) NOTE: After performing the above Solutions work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR


- Code: E003-0003
- Description: Thermistor open circuit detection => In the period from initial rotation to printing, Sub Thermistor 1 detected a temperature of 40 deg C or lower for more than 3 seconds.
- Solutions: Fixing Assembly error, Fixing temperature detection error 1. Check failure between the DC Controller PCB (UN09/ J12) and the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable, open circuit, connector disconnection). -> Replace the part in the case of trapped cable/open circuit 2. Replace the Fixing Assembly 3. Replace the DC Controller PCB (UN09) NOTE: After performing the above Solutions work, go through the following to clear the error: COPIER > FUNCTION > CLEAR > ERR

Support fix printer solution and reset Canon CX-G6400-4":
– Telegramhttps://t.me/hyperaktiv
– Facebookhttps://www.facebook.com/dngnm/

Related sources:
https://nguyendangnam.com/
https://shop.nguyendangnam.com
https://nguyendangnam.com/download-epson-artisan-710-driver-firmware-users-manual-and-wic-key.html
Fix other error code list about printer, https://nguyendangnam.com/epson-driver
Fix other error code list about printer, https://nguyendangnam.com/error-code
https://shop.nguyendangnam.com/product-category/adjustment-program/

Calendar

VIET NAM's Calendars