Canon BJ-200E Driver, Firmware and Manuals for Windows and MacOSCanon BJ-200E Driver, Firmware and Manuals for Windows and MacOShttps://www.magmahdi.com/c/message_boards/find_thread?p_l_id=959813&threadId=24321012024-03-29T01:09:06Z2024-03-29T01:09:06ZCanon BJ-200E Driver, Firmware and Manuals for Windows and MacOSDang Namhttps://www.magmahdi.com/c/message_boards/find_message?p_l_id=959813&messageId=24321002021-12-04T04:27:53Z2021-12-04T04:27:53Z<strong><em>Canon BJ-200E Driver, Firmware and Manuals for Windows and MacOS</em></strong><br /><br /><a href="https://dnasofts.com/"><strong>https://dnasofts.com/</strong></a> is your one-stop shop to find drivers for <em>Canon BJ-200E printer softwares and utilities</em>, or if you need information on the compatibility of Canon products with OS like Windows 7, Windows 8, Windows 10, Windows 11 or Linux, MacOS, ... We have found that our site has everything in this area that you might be looking for!<br /><strong>BJ-200E printer</strong> is best suited for office use and its bundled with many features which makes it a productive and efficient machine. This product supports duplex printing and many other advanced features.<br /><br /><img src="https://dnasofts.com/wp-content/uploads/2021/122021/featured_img/Canon_BJ-200E.jpg" alt="Canon BJ-200E Driver, Firmware and Manuals for Windows and MacOS" title="Canon BJ-200E Driver, Firmware and Manuals for Windows and MacOS" /><br /><br />Get <strong>Epson printer driver, firmware and manual more over here: </strong><a href="https://dnasofts.com/epson-driver/">https://dnasofts.com/</a><br /><br /><strong>Canon BJ-200E Driver</strong><br /><br />- <strong>Canon BJ-200E Drivers</strong> is an intermediate software that helps the transmission of data between computers and printers through USB connections, ports or Wi-Fi. This can be done in order to make printing easier on both sides; it also supports installation/repairing printer devices like monitoring warning parts are not working properly when they need repair or replacement (just like ink). The progress will show up as well as errors such blurred photo prints due do low resolution setting being enabled while scanning - but there'ss no reason you should have this problem if your settings matched what was suggested earlier!<br />- At first glance, it is difficult to understand why anyone would need a driver that fixes Canon BJ-200E printer errors and issues. However there are many reasons someone might have this installed on their computer--maybe they got one piece of paper stuck in the machine causing an 'Paper Jam' error code while trying other things with Photoshop or Microsoft Office? Or maybe you were running low on ink so wanted try cleaning out some dirt inside before calling for help; either way if any type of problem arises users should know exactly where too find WIC utility reset chip (or hack adjustment programs) because finding them elsewhere will only lead more trouble later down road<br /><br /><strong>Download Canon BJ-200E Driver for Windows:</strong><br /><br />- Download Canon BJ-200E Driver for Windows 11: <a href="https://dl.wickeys.net/index.php?act=dl&id=11869&hash=1638333021651"><strong>DOWNLOAD LINK</strong></a><br /><br />- Download Canon BJ-200E Driver for Windows 10 64bit: <a href="https://dl.wickeys.net/index.php?act=dl&id=12577&hash=1638333652402"><strong>DOWNLOAD LINK</strong></a><br /><br />- Download Canon BJ-200E Driver for Windows 10 32bit: <a href="https://dl.wickeys.net/index.php?act=dl&id=13285&hash=1638334052533"><strong>DOWNLOAD LINK</strong></a><br /><br />- Download Canon BJ-200E Driver for Windows 8 64bit: <a href="https://dl.wickeys.net/index.php?act=dl&id=13993&hash=1638334386360"><strong>DOWNLOAD LINK</strong></a><br /><br />- Download Canon BJ-200E Driver for Windows 8 32bit: <a href="https://dl.wickeys.net/index.php?act=dl&id=14701&hash=1638334853266"><strong>DOWNLOAD LINK</strong></a><br /><br />- Download Canon BJ-200E Driver for Windows 7 64bit: <a href="https://dl.wickeys.net/index.php?act=dl&id=15409&hash=1638335357941"><strong>DOWNLOAD LINK</strong></a><br /><br />- Download Canon BJ-200E Driver for Windows 7 32bit: <a href="https://dl.wickeys.net/index.php?act=dl&id=16117&hash=1638335749942"><strong>DOWNLOAD LINK</strong></a><br /><br /><strong><em>Download Canon BJ-200E printer Driver for Mac OS:</em></strong><br /><br />- Download Canon BJ-200E Driver for Mac OS 11.xx: <a href="https://dl.wickeys.net/index.php?act=dl&id=17533&hash=1638336343146"><strong>DOWNLOAD LINK</strong></a><br /><br />- Download Canon BJ-200E Driver for Mac OS 10.xx: <a href="https://dl.wickeys.net/index.php?act=dl&id=17533&hash=1638336343146"><strong>DOWNLOAD LINK</strong></a><br /><br /><strong>How to download softwares or documents of Canon BJ-200E</strong><br /><br />STEP 1: Go to our website and search for <strong>"Canon BJ-200E driver, firmware, manual"</strong><br /><br />STEP 2: Choose your specific <strong>Canon BJ-200E driver, firmware and manual</strong> and click to <strong>Download</strong> button image<br /><br />STEP 3: Wait for the downloading webpage and download the software<br /><br /><img src="https://dnasofts.com/wp-content/uploads/2021/112021/step-download-3.jpg" alt="Canon BJ-200E driver, firmware, manual downloading webpage" title="Canon BJ-200E driver, firmware, manual downloading webpage" /><br /><br />STEP 4: Your downloaded file has been located in <em>Browser Downloaded Page</em><br /><br /><img src="https://dnasofts.com/wp-content/uploads/2021/112021/step-download-4.jpg" alt="Canon BJ-200E driver, firmware, manual downloaded file" title="Canon BJ-200E driver, firmware, manual downloaded file" /><br /><br />STEP 5: Read the instructions to install and start using the softwares.<br /><br /><strong>Canon BJ-200E Firmware</strong><br /><br />- When you use <strong>Canon BJ-200E printer</strong> to print from a computer or sending jobs to another device, you need the <strong>Canon BJ-200E 's firmware</strong>. But if it gets stuck in an error state and can't be fixed by itself anymore then refilling with <strong>original Canon BJ-200E firmware</strong> will come handy as this helps fix unstable components of your machine while diagnosing technical errors occurring on both hardware level with software related problems<br />- The package also includes all necessary tools that are used during these procedures so there isn't anything lost along<br />- The <strong>Canon BJ-200E printer</strong> is more than just a means of reproduction, it has evolved into an essential tool for home and office use. When you need to troubleshoot or service your device call the pros at <a href="https://dnasofts.com/">https://dnasofts.com/</a>!<br />The <strong>Canon BJ-200E original firmware</strong> can fix some errors related with hardware like sensors failure--restarting them in time so they don't fail repeatedly; circuit problems preventing electricity from flowing properly through components on print heads etc...<br />The <strong>Canon BJ-200E original firmware</strong> in your printer is the software that allows it to function. With firmware, Canon BJ-200E printer can be updated remotely via updates sent by manufacturers, which affect how you use and accomplish tasks with your Canon BJ-200E printer - for example speeding up printing time!<br /><strong>Canon BJ-200E Original Firmware</strong> is the software that controls your printer. It allows it to communicate with a computer and do what you want, like printing or copying things! The chip inside this device can be updated remotely so if there are any problems fixed in an update then they will fix them because of how close these two work together.<br /><br /><strong><em>Download Original Canon BJ-200E Firmware for Windows:</em></strong><br /><br />- Original Canon BJ-200E Firmware for Windows: <a href="https://dl.wickeys.net/index.php?act=dl&id=18949&hash=1638337937406"><strong>DOWNLOAD LINK</strong></a><br /><br /><strong><em>Download Canon BJ-200E Firmware for Mac OS:</em></strong><br /><br />- Original Canon BJ-200E Firmware for Mac OS: <a href="https://dl.wickeys.net/index.php?act=dl&id=18241&hash=1638337623399"><strong>DOWNLOAD LINK</strong></a><br /><br /><strong>Canon BJ-200E User Manual</strong><br /><br />- The Canon BJ-200E Manual for your Canon BJ-200E printer includes instructions to fix common problems and issues. It covers basic disassembly, as well as the steps needed when choosing between different ink types or if there's a clogged printhead that needs clearing out with no clear answer on what will work best in these circumstances?<br />- <strong>Canon BJ-200EUser Guides</strong> provide troubleshooting tips such an easy way of getting around features found within any given model; however some may only include limited information compared those containing more detailed explanations - this could be due partially because they're designed specifically towards beginners who might not yet know everything about using certain items<br />- By using <strong>Canon BJ-200E Manual</strong>, you can follow the instructions of the ebook and then you are able to fix errors code or common error like printer is unresponsive, bad print quality, printer won't scan, too many paper jams, prints too slowly, printing is too expensive, can't print from mobile device, Wi-Fi printing takes too long, disassembly or assembly of printer, Canon BJ-200E maintenance, sensor errors, Canon BJ-200E software problem, printer went problem, Canon BJ-200E troubleshooting, printer cable connections inside the product, ...<br />You can use our guide in order to understand all aspects of using this device including installation process and proper usage guidelines so that you never run into any issues while printing or configuring your machine!<br /><br />- Canon BJ-200E User Manuals for Windows: <a href="https://dl.wickeys.net/index.php?act=dl&id=19657&hash=1638340374146"><strong>DOWNLOAD LINK</strong></a><br /><br />- Canon BJ-200E User Manuals for MacOS: <a href="https://dl.wickeys.net/index.php?act=dl&id=19657&hash=1638340374146"><strong>DOWNLOAD LINK</strong></a><br /><br /><strong>[Quick guide] Fix Canon BJ-200E error code list</strong><br /><br />- Code: E001 0001<br />- Description: Fixing Main Thermistor high temperature detection error. The Fixing Main Thermistor in the Fixing Unit detected 284 deg C or higher for 0.2 sec or longer.<br />- Solutions: [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Solutions] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the Solutions work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES<br /><br /><br />- Code: E001 0002<br />- Description: Fixing Sub Thermistor (Front) high temperature detection error. The Fixing Sub Thermistor (Front) in the Fixing Unit detected 295 deg C or higher for 0.2 sec or longer.<br />- Solutions: [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Solutions] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the Solutions work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES<br /><br /><br />- Code: E002 0002<br />- Description: Fixing Sub Thermistor (Front) open circuit detection error. The Fixing Sub Thermistor (Front) detected a temperature of 40 deg C or lower for 3 sec or longer from when the Fixing Heater was turned ON until start of PI control<br />- Solutions: [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Solutions] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the Solutions work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES<br /><br /><br />- Code: E002 0003<br />- Description: Fixing Sub Thermistor (Rear) open circuit detection error. The Fixing Sub Thermistor (Rear) detected a temperature of 40 deg C or lower for 3 sec or longer from when the Fixing Heater was turned ON until start of PI control.<br />- Solutions: [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Solutions] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the Solutions work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES<br /><br /><br />- Code: E002 0004<br />- Description: Fixing Main Thermistor temperature increase detection error. The Fixing Main Thermistor detected a temperature increase of 1 deg C for less than 5 sec from when the Fixing Heater was turned ON until start of PI control.<br />- Solutions: [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Solutions] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the Solutions work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES<br /><br /><br />- Code: E003 0004<br />- Description: Fixing Main Thermistor low temperature detection error.The Fixing Main Thermistor detected a temperature of 80 deg C or lower for 1 sec or longer from start of PI control until completion of the last rotation (the Fixing Heater was turned OFF).<br />- Solutions: [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Solutions] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the Solutions work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES<br /><br />- Code: E003 0005<br />- Description: Fixing Sub Thermistor (Front) low temperature detection error. The Fixing Sub Thermistor (Front) detected a temperature of 80 deg C or lower for 1 sec or longer from start of PI control until completion of the last rotation (the Fixing Heater was turned OFF).<br />- Solutions: [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Solutions] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the Solutions work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES<br /><br /><br />- Code: E003 0006<br />- Description: Fixing Sub Thermistor (Rear) low temperature detection error. The Fixing Sub Thermistor (Rear) detected a temperature of 80 deg C or lower for 1 sec or longer from start of PI control until completion of the last rotation (the Fixing Heater was turned OFF).<br />- Solutions: [Related parts] • Harnesses from the DC Controller PCB to the Fixing Thermistor 1. DC Controller PCB (UN04/J121) to Fixing Drawer (J1001DA) (Unit of replacement: FIXING DRAWER ASSEMBLY) 2. Fixing Drawer (J1001LA) to Relay Connector (8P) (Unit of replacement: CABLE, DRAWER RELAY) 3. Relay Connector (8P) to Fixing Thermistor (TH02) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the Low Voltage Power Supply PCB (UN01/J302) and the AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Solutions] 1. Check/replace the related harness/cable, connector and parts. 2. After performing the Solutions work, go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES<br /><br /><br />- Code: E004 0001<br />- Description: Fixing Relay welding detection error. Zero cross interruption was detected although the Fixing Relay was not turned ON.<br />- Solutions: [Related parts] • Harness from the DC Controller PCB (UN04/J115) and the Low Voltage Power Supply PCB (UN01/J322) (Unit of replacement: POWER SUPPLY ASSEMBLY) • Harness between the DC Controller PCB (UN04/J121) and the Fixing Drawer (J1001D<img alt="emoticon" src="https://www.magmahdi.com/o/magma-journey-theme/images/emoticons/cool.gif" > (Unit of replacement: FIXING DRAWER ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Solutions] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES<br /><br /><br />- Code: E004 0002<br />- Description: Current detection circuit error. Current outside the specified range flowed to the Fixing Heater when the heater was turned ON. Or, failure of fixing current detection circuit was detected.<br />- Solutions: [Related parts] • Harnesses from the Low Voltage Power Supply PCB to the Fixing Heater 1. Low Voltage Power Supply PCB (UN01/J302) to AC Interlock Switch (SW12) (Unit of replacement: CABLE, AC INTERLOCK SWITCH) 2. AC Interlock Switch (SW12) to Fixing Drawer (J1001) (Unit of replacement: FIXING DRAWER ASSEMBLY) 3. Fixing Drawer (J1001) to Relay Connector (3P) (Unit of replacement: CABLE, DRAWER RELAY) 4. Relay Connector (3P) to Fixing Heater (H1 and H2/J1115) (Unit of replacement: FIXING FILM ASSEMBLY) • Harness between the DC Controller PCB (UN04/J121) and the Fixing Drawer (J1001D<img alt="emoticon" src="https://www.magmahdi.com/o/magma-journey-theme/images/emoticons/cool.gif" > (Unit of replacement: FIXING DRAWER ASSEMBLY) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • Low Voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Solutions] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES<br /><br /><br />- Code: E009 0000<br />- Description: Fixing pressure timeout error. The Fixing Pressure Release Sensor did not detect ON status within 10 sec after the start of pressure application operation for fixing.<br />- Solutions: [Related parts] • Harnesses from the DC Controller PCB to the Fixing Pressure Release Sensor 1. DC Controller PCB (UN04/J122) to Relay Connector (11P) (Unit of replacement: CABLE, FEED) 2. Relay Connector (11P) to Fixing Pressure Release Sensor (PS13) (Unit of replacement: PAPER DELIVERY DRIVE ASSEMBLY) • Harnesses from the DC Controller PCB to the Fixing Motor 1. DC Controller PCB (UN04/J122) to Relay Connector (8P) (Unit of replacement: CABLE, FEED) 2. Relay Connector (8P) to Fixing Motor (M09) (Unit of replacement: FIXING DRIVE MOTOR ASSEMBLY) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Fixing Pressure Release Sensor (PS13) • Fixing Drive Unit (Unit of replacement: FIXING DRIVE ASSEMBLY) [Solutions] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES<br /><br /><br />- Code: E009 0001<br />- Description: Fixing disengagement timeout error. The Fixing Pressure Release Sensor did not detect OFF status within 10 sec after the start of fixing disengagement operation.<br />- Solutions: [Related parts] • Harnesses from the DC Controller PCB to the Fixing Pressure Release Sensor 1. DC Controller PCB (UN04/J122) to Relay Connector (11P) (Unit of replacement: CABLE, FEED) 2. Relay Connector (11P) to Fixing Pressure Release Sensor (PS13) (Unit of replacement: PAPER DELIVERY DRIVE ASSEMBLY) • Harnesses from the DC Controller PCB to the Fixing Motor 1. DC Controller PCB (UN04/J122) to Relay Connector (8P) (Unit of replacement: CABLE, FEED) 2. Relay Connector (8P) to Fixing Motor (M09) (Unit of replacement: FIXING DRIVE MOTOR ASSEMBLY) • Fixing Unit (Unit of replacement: FIXING ASSEMBLY) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) • Fixing Pressure Release Sensor (PS13) • Fixing Drive Unit (Unit of replacement: FIXING DRIVE ASSEMBLY) [Solutions] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES<br /><br /><strong>Support fix printer solution and reset Canon BJ-200E:</strong><br />– <strong>Telegram</strong>: <a href="https://t.me/hyperaktiv"><strong><em>https://t.me/hyperaktiv</em></strong></a><br />– <strong>Facebook</strong>: <a href="https://www.facebook.com/dngnm/"><strong><em>https://www.facebook.com/dngnm/</em></strong></a><br /><br />Related sources:<br /><a href="https://nguyendangnam.com/">https://nguyendangnam.com/</a><br /><a href="https://shop.nguyendangnam.com">https://shop.nguyendangnam.com</a><br /><a href="https://nguyendangnam.com/download-epson-artisan-710-driver-firmware-users-manual-and-wic-key.html">https://nguyendangnam.com/download-epson-artisan-710-driver-firmware-users-manual-and-wic-key.html</a><br />Fix other error code list about printer, <a href="https://nguyendangnam.com/epson-driver">https://nguyendangnam.com/epson-driver</a><br />Fix other error code list about printer, <a href="https://nguyendangnam.com/error-code">https://nguyendangnam.com/error-code</a><br /><a href="https://shop.nguyendangnam.com/product-category/adjustment-program/">https://shop.nguyendangnam.com/product-category/adjustment-program/</a>Dang Nam2021-12-04T04:27:53Z